bante900P multi-parameter meter is capable of measuring up to 9 water quality parameters, including pH, ORP, Ion, Conductivity TDS, Salinity, Resistivity, Dissolved Oxygen, etc.
General Features:
* Automatic Temperature Compensation ensures highly accurate measurements over the entire range.
* Calibration due reminder helps you to calibrate meter regularly.
* Automatic endpoint function freezes stable measured values.
* Help message as a operational guide to helps you understand how to use meter.
* Setup menu lets user customize the calibration points, stability conditions, date and time to meet measurement requirements.
* Expanded memory stores and recalls up to 500 readings.
* Built-in real-time clock stamps stored data to meets GLP.
* Stored data can be transferred into PC via USB communication interface.
| Model | Bante900P |
| pH | |
| Range | -2.000~20.000pH |
| Accuracy | ±0.002pH |
| Resolution | 0.1, 0.01, 0.001pH, Selectable |
| Calibration Points | 1 to 5 points |
| Calibration Solutions | USA, NIST, DIN or User-defined |
| Temperature Compensation | 0~100°C, 32~212°F |
| Compensation Mode | Manual or Automatic |
| mV | |
| Range | -1999.9~1999.9mV |
| Accuracy | ±0.2mV |
| Resolution | 0.1, 1mV, Selectable |
| Calibration Points | 1 point (only for Relative mV mode) |
| Calibration Range | ±200mV |
| Ion | |
| Range | 0.001~19999ppm, mg/L, mol/L (Refer to the range of ISE) |
| Accuracy | ±0.5% F.S (Monovalent), ±1% F.S (Divalent) |
| Resolution | 0.001, 0.01, 0.1, 1 |
| Calibration Points | 2 to 5 points |
| Calibration Solutions | 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000ppm, mg/L, mol/L |
| Temperature Compensation | 0~100°C, 32~212°F |
| Compensation Mode | Manual or Automatic |
| Conductivity | |
| Range | 0~20.00, 200.0, 2000µS/cm, 20.00, 200.0mS/cm |
| Accuracy | ±0.5% F.S |
| Calibration Points | 1 to 5 points |
| Calibration Solutions | 10µS/cm, 84µS/cm,1413µS/cm,12.88mS/cm,111.8mS/cm |
| Temperature Compensation | 0~100°C, 32~212°F, Manual or Automatic |
| Temperature Coefficient | 0.0~10.0%/°C |
| Compensation Modes | Linear or Pure Water |
| Cell Constant | K=0.1, 1, 10 or User-defined |
| Normalization Temperature | 20°C or 25°C |
| TDS | |
| Range | 0~100ppt (Max. 200ppt, depending on factor setting) |
| Accuracy | ±1% F.S |
| TDS Factor | 0.1~1.0 (Default 0.5) |
| Salinity | |
| Range | 0~10ppt (Max. 80ppt) |
| Accuracy | ±1% F.S |
| Measurement Modes | Seawater or Practical Salinity |
| Resistivity | |
| Range | 0~100MΩ |
| Accuracy | ±1% F.S |
| Resolution | 0.01, 0.1, 1 |
| Dissolved Oxygen | |
| Range | 0.00~20.00mg/L (or ppm) |
| Accuracy | ±0.2mg/L |
| Resolution | 0.01mg/L |
| Calibration Points | 1 or 2 points |
| Temperature Compensation | 0~50°C, 32~122°F, Automatic |
| Pressure Correction | 60.0~112.5kPa, 450~850mmHg |
| Salinity Correction | 0~50g/L |
| % Saturation of Oxygen | |
| Range | 0.0~200.0% |
| Accuracy | ±2.0% |
| Resolution | 0.1, 1% |
| Temperature | |
| Range | 0~105°C, 32~221°F |
| Accuracy | ±0.5°C, ±0.9°F |
| Resolution | 0.1°C |
| Calibration Points | 1 point |
| Calibration Range | Measured value ±10°C |
| Others | |
| Hold Function | Manual or Automatic |
| Stability Conditions | Low or High |
| Calibration Due | 0 to 31 days |
| Power Off | Manual or Automatic (10, 20, 30 minutes) |
| Reset Function | Yes |
| Memory | Stores up to 500 data sets |
| Output | USB Communication Interface |
| Connector | BNC, 6-pin Mini Plug |
| Power Requirements | 3×1.5V "AA" Batteries |
| Battery Life | Approximately 150 hours (Turn off the backlit) |
| Dimensions | 170(L)×85(W)×30(H)mm |
| Weight | 300g |
Ying
